CAIS Kit for building a cantilever sliding gate up to 4.5 m with a NICE Robus RBS400 drive, galvanized
NEW| Product availability: | In stock | We normally dispatch goods within 24 hours. |
|---|
in stock
€1,044.99 including VAT
| Weight |
|---|
| 67 kg |
Description of CAIS Kit for building a cantilever sliding gate up to 4.5 m with a NICE Robus RBS400 drive, galvanized
KIT ENZO SZ 03 component kit for building a cantilever sliding gate with a passage width of up to 4.5 m and a gate weight of up to 400 kg. All components are galvanized.
| Set SADA-RBS400-ENZO-SZ-03 contains: | ||||
|---|---|---|---|---|
|
1 × | C-profile 73x61x3,5mm with screw holes, Zn. 6m | CAIS-STAGE-SZ-6 | |
|
A guide C-profile screwed to the bottom of the gate, allowing it to run on carriages anchored in a concrete foundation. Galvanized finish.
|
Details 
|
|||
|
2 × | SPEED S trolley with eight bearing rollers | CAIS-SPEED-S | |
|
Galvanized steel trolley with 8 metal wheels. |
Details
|
|||
|
1 × | Bottom ramp – for C-profile 73x61x3.5 | CAIS-RUN-S | |
|
The bottom guide ramp for a sliding gate slides into the C-profile and is secured to it with a clamping plate. When the gate closes, the ramp engages with the bottom stop to relieve the load on the gate. |
Details
|
|||
|
1 × | Bottom end stop for C-profile 73x61x3.5 | CAIS-LAST-S | |
|
Run-off pocket mounted at the bottom of the gate stop post. Relieves the compressive and tensile forces acting on the roller carriages when the gate is closed. |
Details
|
|||
|
1 × | Top guide with two rollers for sliding gates | CAIS-FRS2 | |
|
Gate guide for vertical stabilization of the gate in the transverse direction. |
Details
|
|||
|
1 × | C-Profile End Cap 73x61x3.5 | CAIS-PILOT-SN | |
|
The end cap for a sliding gate C-profile is fitted at the beginning and, if required, at the end of the guide C-profile. It slides into the C-profile and is secured to it with a clamping plate. |
Details
|
|||
|
1 × | 73x61x3.5 C-profile end cap with ramp mounting | CAIS-PILOT-SR | |
|
The CAIS PILOT SR end cap for the sliding gate C-profile is installed at the beginning of the guide C-profile. The end cap attaches to the CAIS RUN S gate stop. |
Details
|
|||
|
1 × | NICE Robus RBS400 standalone gate operator | NICE-RBS400-A | |
|
NICE Robus RBS400 gate operator for gates with a leaf weighing up to 400 kg and a leaf length of 8 m. The operator includes a built-in NICE MCU1R30 control unit with an integrated receiver.
|
Details
|
|||
|
1 × | NICE MYGO4 - four-channel remote control | NICE-MYGO4 | |
|
NICE MYGO4 - four-channel remote control, rolling code, 433.92 MHz |
Details
|
|||
|
1 × | NICE EPMB - Era Photocell Medium - photocells with BlueBUS connection | NICE-EPMB | |
|
Safety photocells are installed on either side of the opening. They create an infrared beam which, when interrupted by a car or pedestrian, for example, sends a signal to the drive to stop the gate or prevent it from opening. |
Details
|
|||
|
1 × | NICE ELDC LED Beacon with Antenna | NICE-ELDC | |
|
NICE LED ELDC flashing warning light made of impact-resistant polycarbonate with a built-in antenna for greater remote-control range (up to 150 m). |
Details
|
|||
|
5 m | Rack with metal reinforcement | LZ-1-1 | |
|
A sliding gate with a fixed rack is moved by the drive gear via a rack-and-pinion mechanism. |
Details
|
|||
|
1 × | Installation Manual for the NICE ROBUS RBS 400 Gate Opener |
Download
|
|
|
Installation manual with illustrated wiring diagrams and instructions for programming and pairing remote controls. |
||||
|
|
1 × | Installation Manual for the CAIS Cantilever Kit |
Download
|
|
|
Installation manual with illustrated wiring diagrams and instructions for programming and pairing remote controls. |
||||
Set of screws and rivet nuts for mounting
2x Inductive Switch
You may want to purchase a BiDi-WiFi module (optional accessory). It lets you control the gate from your phone via MyNice and use MyNice Pro to program the operator and change its supported advanced settings.
CAIS ENZO SZ 03 KIT: BENEFITS AND FEATURES
- Easy to install thanks to carefully designed details, and quick to fit by bolting the C-profile to the structure, eliminating the need to weld it in place.
- Mounting bolts and rivet nuts are included for attaching the C-profile to the structure through the holes in the profile, spaced at least 400 mm apart.
- The hot-dip galvanized C-profile (270 g/m²), with a serial number and 100% tested with the rollers, is spot-on accurate.
- High-quality roller bearings. The centers of the trolley wheels are drilled, not laser-cut.
- Tested from -37°C to +50°C.
- German steel. Japanese robots. Made in the Czech Republic.
EXAMPLE OF SUITABILITY: CAIS ENZO SZ 03 KIT FOR BUILDING A CANTILEVER SLIDING GATE
The kit is suitable for a passage width of up to 4.5 m and a total gate weight of 450 kg. The following drawing shows the dimensions for example passage widths, together with recommended structural profiles. The table below lists the dimensions for each passage width of a cantilever sliding gate.
How can I order this item?
Choose the option that suits you:
- order online: use the buy button to add the goods to your shopping cart (you will find the buy button here in the product variants table).
- order by email: place your order at [email protected]
