NICE Toona TO5605 - single gate operator for swing gates up to 5 m/500 kg per leaf


Product availability: to the question

The product may not be available, contact us for more information.

NICE Toona TO5605 - single gate operator for swing gates up to 5 m/500 kg per leaf NICE Toona TO5605 - single gate operator for swing gates up to 5 m/500 kg per leaf
NICE-TO5605
to the question
€355.45 excluding VAT
€437.20 including VAT

 pcs
Weight
7,00 kg

Description of NICE Toona TO5605 - single gate operator for swing gates up to 5 m/500 kg per leaf

  • Reversible
  • 230V
  • Fast
  • With a microswitch limit stop for opening

Operating range

For a gate leaf weighing up to 500kg and measuring up to 5m, according to the following usage chart:

NICE Toona 5 operator usage limits

Compatible control units

Technical specifications

Power supply 230V
Current draw 1,3A
Power 300W
Speed 0,016m/s
Force 1800N
Cycles/hour* 50
Protection rating IP44
Operating temperature -20°C to +50°C
Dimensions 965x115x105mm
Weight 7kg

* under optimal installation conditions

I. Installing the rear mounting bracket

Diagram showing the NICE Toona operator opening inward Diagram showing the NICE Toona operator opening outward
Inward opening diagram Outward opening diagram

 

Calculate the position of the rear bracket using the chart, from which you can determine dimensions A and B and the maximum opening angle. Please note that values A and B must be similar (ideally identical) to ensure the operator moves smoothly in a linear motion.

Installation chart for the NICE Toona TO5605 operator Illustrative example of calculating the NICE Toona operator installation dimensions
Calculation chart Example of reading values from the chart

 

Calculation procedure:

  1. Measure the distance C from the diagram
  2. On the chart draw a horizontal line crossing the measured value C
  3. Where this line intersects the DIL (Recommended Installation Line), you can determine the maximum opening angle
  4. If the intersection is below the t level, you will need to adjust the values to move the intersection above this level
  5. If the intersection is above the t level, everything is fine; however, if the specified maximum opening angle is unsuitable, you will need to adjust the value of A and, if necessary, the value of B, so that they are similar (ideally identical)

Before fastening the bracket to the post or wall, cut it to the required length to match dimensions A and B and weld it to the mounting plate.

Cut the bracket to the required length Weld the shortened bracket to the mounting plate
1. Cut the bracket to the required length 2. Weld the shortened bracket to the mounting plate

 

The package includes a 150 mm bracket. If you need a longer bracket for special situations, or if you need the gate to open outward, we recommend ordering the extended NICE PLA6 bracket.

Before attaching the rear bracket, check that the front bracket will align with the solid part of the gate leaf, as the front and rear brackets differ in height, as shown in the picture.

 

Difference F = 44mm.

 Height difference between the front and rear brackets

If everything is suitable, attach the rear bracket to the post or wall using screws, wall plugs and washers.

II. Installing the front mounting bracket

The front bracket must be fitted to the gate leaf at a distance determined by the values D and E, which you can find in the table (value D is fixed at 880 mm):

A 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280
E 780 770 760 750 740 730 720 710 700 690 680 670 660 650 640 630 620 610 600

 

The supplied package includes a weld-on bracket. If you would prefer a screw-on bracket, we recommend ordering the alternative NICE PLA8 screw-on bracket.

  1. Calculate from the table value E
  2. Calculate the height according to the diagram bracket heights (view image)
  3. Attach the bracket to the gate leaf (if welding the bracket, we recommend tack-welding it only for now)

III. Mounting the gate operator on the rear bracket

Mounting the NICE Toona operator on the rear bracket
  1. Attach the motor to the bracket as shown in the diagram using the supplied rear bracket pin, washer and nut.
  2. Tighten the nut fully, then loosen it by 1/10 of a turn so that the gate operator can rotate

 

IV. Mounting the gate operator on the front bracket

Mounting the NICE Toona operator on the front bracket
  1. Attach the operator to the bracket as shown in the diagram using the supplied pin and washer.
  2. Tighten the pin fully

 

V. Adjusting the mechanical travel stop

If using the internal mechanical travel stop, which the operator reaches when opening, external ground stops are not required. Adjust as follows:

Adjusting the mechanical travel stop on the NICE Toona operator
  1. Release the operator according to the operator release instructions
  2. Loosen the mechanical stop screw
  3. Manually move the gate leaf to the desired open position
  4. Move the entire mechanical stop against the pin and tighten the screw as shown in the diagram
  5. If both stops are used, repeat steps 2–4 for the front stop (opening stop) and the rear stop (closing stop) mechanical stop
  6. Manually move the gate leaf to the closed position and lock the operator

 

How can I order this item?

Choose the option that suits you:

  1. order online: use the buy button to add the goods to your shopping cart (you will find the buy button here in the product variants table).
  2. order by email: place your order at [email protected]

Ask us anything about NICE Toona TO5605 - single gate operator for swing gates up to 5 m/500 kg per leaf

Product: NICE Toona TO5605 - single gate operator for swing gates up to 5 m/500 kg per leaf
Name:
Email:
Phone:
Message:
This page is protected by Google reCAPTCHA.
Print page Print page